FRP water tank is divided into two types: FRP assembled water tank and SMC combined water tank. It is light weight, no rust, no leakage, good water quality, wide range of use, long service life, good insulation performance, beautiful appearance, easy installation, cleaning and maintenance. The features of simplicity and adaptability are widely used in hotels, restaurants, schools, hospitals, industrial and mining enterprises, public institutions, residential houses, and office buildings. They are ideal products for public living, fire-fighting and industrial water storage facilities. Next, Xiao Bian introduced the construction plan of the FRP water tank and the precautions for using the FRP water tank. FRP tank installation and construction plan 1, first level the cement on the plane, so that it is in the same plane, the error should not exceed ± 0.5cm. 2. Welded channel steel: The channel steel is welded according to the size of the tank, the size of which is consistent with the size of the tank bottom plate. After welding of the channel steel, the diagonal measurement size, the error is ± 0.5cm, and all the welds are to be connected evenly and the seams are consistent . 3, install the bottom help: According to the printing instructions on the tank list, arranged, connected to the bottom of the tank, while adding sealant between the veneer, with 10 bolts, so that the bottom seal is solid, bolt force To evenly increase the force, apply 3-4 times of force to each bolt. Do not use too much force at one time. Otherwise, cracks may occur due to uneven force. 4. Use auxiliary angle iron to connect plates and plates to make the tank more secure. 5, install the help: According to the printing plate number and instructions on the tank board, find out the helper of each layer of the water tank body, and separate in advance, use bolts to assemble the body, set the tank board well, correct, so that the body can use Bottom to form a 90-degree angle, and seals, bolts. 6, install the inner lacing: inner lacing according to the size of the tank, find the number and length of the lacing. Use lacing boards to measure the tightening position of the lacing on the wire, drawing, punching, pulling on the wire, and tightening, so that the flattening of the lacing is balanced with the tank body. If there is a large error between the box and the lacing, the error can be adjusted by adjusting the tightening degree of the bolt until the error is minimized. 7. Install the cover plate: At the end, install the top cover plate of the water tank and evenly tighten the bolts. Do not use too much force or too little. After adjusting all the fasteners of the water tank, open the position according to the drawing and open the water pipes. Flange to dock the valve. 8. After the water tank is installed, conduct a unified inspection and adjustment. The test water does not leak. FRP water tank use matters needing attention 1. FRP water tanks can only contain cold and warm water. It is prohibited to use water tanks to hold hot water or other liquids, especially acidic and alkaline corrosive liquids. 2. During the installation or transportation of the FRP water tank board, handle it gently to avoid collision of the tank board with a sharp hard object. It is forbidden to use wrenches and other hard things to beat the board surface. 3. The use of an open fire next to the fiberglass tank may cause fire. Therefore, when welding, it is necessary to take isolation and protection measures to prevent Mars from splashing. After the tank is installed for the first time, it must be cleaned twice before it can be used formally. 4. After the FRP water tank is installed, a full water test must be performed: After the water tank assembly is completed, close the water outlet pipe and the drain pipe, open the water inlet pipe, check the side of the water pipe, and fill it until it is full. After 24 hours, see no seepage. If water leakage occurs in the tank, there must be a problem with the quality or installation of the fiberglass tank. When leaks occur, do not be distracted by the installation staff. There are two reasons for leakage of the fiberglass tank: (1) FRP tanks Quality problem; At this time, it is necessary to negotiate with the manufacturer to request return and exchange; Second, the problem of water tank installation process, the general connection of the water tank board will be found leaking, which is likely due to the installation staff's mistakes, they must be required to carry out anti-work . FRP tank characteristics 1. The high reactivity and inter-benzene type food-grade unsaturated polyester resin selected for FRP water tanks has few residual styrene after the resin is cured. It can meet the demand of cleaning, and has good water resistance. After long-term use, it is still Can adhere to meet the mechanical properties. 2, full use of alkali-free glass fiber, the alkali metal oxide content is less than 1, this glass fiber is equivalent to E glass fiber. It has excellent chemical stability, electrical insulation and mechanical properties. Editor's summary: Regarding the construction of the FRP tank construction project and the precautions for the use of the FRP water tank, it is introduced here and I hope to be helpful to everyone. If you want to know more related information, you can pay attention to this website information. Water tank Squatting pan Water tank Water leaking Water tank Water leaking Toilet tank Water leak Zhongda Steel Structure , https://www.zhongdametal.com
FRP water tank installation construction plan FRP water tank use matters needing attention